7200 Series Electromechanical Closer/Holder

The 7200 Series is a multi-point electromechanical closer/holder that provides flexibility to installers and facility managers. Shipped standard with selective hold open, the 7200 Series is designed to hold the door open at any point up to 180°. Available for push or pull side mounting, these units can be ordered with a remote wireless door release.

Specifications

Closer for __________ doors shall be electromechanical (with integral smoke detector) and completely enclosed in a metal cover. Units shall be surface mounted to the frame face [on the pull (hinge side) on the push (opposite hinge side)] of the door [and shall project no more than 2-5/8" (67mm) from the surface of the frame]. (Closer shall be installed in the header of the frame, and the slide track mortised into the door’s top rail). Closer unit shall be hydraulic, full rack and pinion type with a cast aluminum alloy shell. Hydraulic fluid shall be non-gumming and non-freezing. Closer unit shall have two non-critical valves to independently regulate closing and latch speed. It shall also have an adjustable backcheck with a hex-key. Closer unit shall have spring power adjustment to permit a 50% increase in closing power over the minimum closing force for any size. Electromechanical Closer shall have (Infinite) (Selective) Hold Open (Free Swing Operation) and shall be able to attain a maximum opening of 180° (with hold open to 175°). Unit to be fail safe and must close the door during any electrical power interruption to the unit. (Closer/Holder to be Executive Door Holder/Release with release actuated by battery operated hand-held controller). Unit(s) to operate on (_______VAC, 60Hz) (_________ VDC) and will accept (surface) (concealed) wiring. Amperage draw shall not exceed (.086 Amps for 24VAC/DC) (.051 Amps for 120VAC) units. Supplier to coordinate electrical requirements with electrical and alarm system engineers. Wiring (and conduit) by others. Electromechanical Units to be Norton® Series 7200 (Closer/Holder) (Free Swing Releasing Device), (Executive Door Holder/Release).

Finishes

613E Dark Oxidized Satin Bronze, Equivalent	689 Aluminum	690 Statuary Bronze	691 Dull Bronze	693 Black	694 Medium Amber	696 Gold
BSP Black Suede Powder Coat	WSP White Suede Powder Coat

7200 Documents

Catalog

Installation Instructions

Templates

Wiring Diagrams

Features

Multi-point, electromechanical closer/holder
Selectable hold open time standard; infinite hold open can be set in the field by turning the cam
Push or pull side mounting
Handed
Spring sizes 3, 4 or 5 (pull side) and sizes 4, 5 or 6 (push side)
Fail Safe
Concealed or surface wiring

Selective Hold Open (Standard): The door will hold open at any degree of opening beyond a pre-set hold open point, up to 175°, with a maximum allowable door opening of 180° (exception series 7250 at 110°).
Infinite Hold Open: The door will hold open at any degree of opening up to 175°, with a maximum allowable door opening of 180° (exception series 7250 at 110°). Can be set in the field by turning cam.

Primary Unit: 7200MPDO

Consists of an on-board power supply (for 120VAC input option) or a terminal strip (for 24VDC input option), an integral smoke detector module and a door closer assembly with internal electrohydraulic holder capability. A Primary Unit can control a single door or one leaf of a pair of doors. A 24VDC Support Unit is required on the opposite door leaf.

Support Unit: 7200MPSO

Identical in size to the Primary Unit, the Support Unit consists of an on-board power supply (for 120VAC) input option) or a terminal strip (for 24VDC input option) and a door closer assembly with internal electrohydraulic holder capability. This unit (120VAC or 24VDC is intended to control a single door or a pair of doors wher the building's alarm system monitors the power to the Support Unit (24VDC) to control the inactive leaf of a pair of doors where the active leaf is controlled by a Primary Unit.

Executive™ Unit: RFS Suffix

Identical in size and appearance to the Primary Unit, the Executive Unit consists of an on-board power supply (for 120VAC) input option) or a terminal strip (for 24VDC input option) a 433MHz radio frequency receiver and a door closer assembly with internal electrohydraulic holder capability. Unit is intended to provide remote wireless release of a door that has been manually placed into the electrified hold open position. Not intended for use in life safety applications.

Typical Applications

Patient rooms
Executive offices
Material storage rooms

Libraries
Storage rooms

Electrical Data

Input Power: 120VAC or 24VDC
Current Draw: Primary Units = < 0.25A, Support Units = <0.1A

Certifications

ANSI/BHMA A156.15 certified
Listed by Underwriters Laboratories for labeled fire door

Manufactured in an ISO 9001 facility
2-year limited warranty

Request Information

Discuss your needs directly; fill out the form below.